Understanding Why a Plumber is Needed to Install Your Dishwasher
Understanding Why a Plumber is Needed to Install Your Dishwasher
Blog Article
Click Here
From hauling a dish washer right into your home to affixing the water links, installing a dish washer can take up to five hours. A plumber will have the right devices on hand and can install your brand-new dish washer in under 2 hrs.
Not Installing Your Dishwashing Machine Properly Can Lead to a Mountain of Problems
Not just can installing a dish washer properly void your warranty, but it can also create a mess. If you do not set up the supply line appropriately, you might deal with leaks-- or even worse, a flood. You may also experience a "water hammer"-- when the water runs too quickly through your pipes as well as causes loud shaking sounds. If you improperly mount your dishwasher to the garbage disposal, you might observe pungent smells or have residue on your dishes.
An Improper Setup Can Invalidate the Dishwasher's Guarantee
Prior to setting up a dishwasher on your very own, you should read the guarantee very carefully. Unless you are helpful and have experience installing dishwashers, you need to hire a plumber so you do not risk your guarantee.
Installing a Dishwasher Calls For a Range of Tools
If you do not have a variety of devices on hand, you may require to make a trip to Lowe's or House Depot. To mount a dishwasher, you require the following tools: pliers, a flexible wrench, a set of screwdrivers, a tube cutter, and opening saws.
A Plumber Can Check the Supply Lines
A supply line, particularly a dish washer adapter, links the dish washer to a water source. A plumber can ensure that the line is compatible with both your dish washer and water resource if you buy a brand-new supply line. If you make a decision to use an existing supply line, an expert plumber can inspect it to ensure that it remains in good condition and also does not have any leakages.
A Plumber Can Complete the Job Affordably as well as Quickly
A plumber can install your dishwasher in one to 2 hrs. The ordinary plumber will not charge even more than a couple of hundred bucks to install your dish washer.
From carrying a dishwasher into your house to affixing the water connections, setting up a dish washer can take up to 5 hrs. To make your life easier and to avoid mounting a dishwashing machine incorrectly, we suggest hiring a specialist plumber. A plumber will certainly have the right devices on hand and also can install your new dishwashing machine in under two hours. Unless you are helpful and have experience setting up dishwashers, you must hire a plumber so you do not risk your service warranty.
A supply line, specifically a dishwasher adapter, links the dishwashing machine to a water resource.
How To Install A Dishwasher
Installing A Dishwasher Yourself
Just like other home appliances, a dishwasher helps to make chores less time-consuming and free of hassle. Most modern kitchens have a dishwasher or a cabinet space for dishwasher installation built into them. An older kitchen with no dishwasher or cabinet space for one might require a little reconstruction to accommodate dishwasher installation.
Installing a dishwasher requires basic knowledge of plumbing and electrical wiring. This article contains the steps involved in dishwasher installation, dishwasher installation tips, things to consider when installing a dishwasher in a kitchen that previously had no dishwasher in it, and tips for maintaining a dishwasher.
Steps Involved In Dishwasher Installation
Step One: Gather the Necessary Supplies
Gather all the required items and keep them near the installation site for easy reach. The materials and tools you will require include the following:
A screwdriver • A hose clamp • Duct tape (optional) • A brass fitting • Teflon tape • A pair of pliers • An adjustable wrench • A drill • Braided steel water line • A pair of rubber hand gloves (optional) • Wire nuts Step Two: Take Safety Measures
First, turn off the power socket and unplug the power cord if it is a plug-in dishwasher. Then, proceed to turn off the circuit breaker. Next, turn off the hot water shut-off valve under the kitchen sink and run the tap to ensure the water supply is shut off. Protect your kitchen floor close to the installation area with an old rug or a piece of drop cloth.
Step Three: Remove the Old Dishwasher
This step only applies if your kitchen has an old dishwasher that you want to replace. Remove the cabinet door to gain complete access to the old dishwasher. Next, remove the cover of the access panel located at the bottom front side of the dishwasher. Locate the junction box inside the access panel.
Now, unscrew the terminal screws holding the wires in place at the junction box. Then, remove and tuck the wires out of the way with duct tape. Locate the dishwasher water inlet tube, undo the brass fitting and disconnect the water supply pipe from it. Put the disconnected end of the water supply line pipe into a bucket or bowl to collect any water remaining in it.
Reach down beneath the sink to undo the drain hose. Loosen, then clamp and disconnect the drain hose of the dishwasher from the tailpiece of the sink. Next, put the disconnected end of the drain hose into a bucket to collect the water and debris.
With all the connections out of place, remove the screws holding the dishwasher in place with a screwdriver, gently pull the dishwasher out from the cabinet and set it aside. You can use a piece of cloth or towel to clean up the mess made or any water spillage on the floor. Also, clean the cabinet where the old dishwasher was before installing a new one.
Skip this step if you are having a dishwasher installed for the first time in your kitchen.
Step Four: Install the New Dishwasher
Connect the Water Supply
Wrap Teflon tape on the tip of the water inlet pipe located at the bottom of the dishwasher. Screw on the 90 degrees brass fitting to the taped inlet pipe and tighten it with an adjustable wrench. Most dishwasher units do not include a brass fitting, but they are available at hardware stores.
Once you have the fitting, connect the new water supply line to the elbow of the brass fitting. Pass the other end of the waterline through one of the cabinet holes and place it on the floor beneath the kitchen sink.
Attach the Drain Line
Locate the dishwasher drain standout pipe, connect the drain line to the dishwasher, and secure the connection with a hose clamp. Pass the other end of the drain line through the cabinet hole and place it towards the sink drain tailpiece
Slide the Dishwasher into Place
Attach the adjustable legs to the front of the dishwasher. Carefully slide the dishwasher under the countertop into the cabinet. Stop halfway and ensure everything is in a good position before sliding it in completely. Finish hooking up the water line by connecting the other end to the dual shut-off valve located under the kitchen sink.
Proceed to connect the drain hose through an air gap to your garbage disposer, if you have any, or to the drain tailpiece of your sink. If you do not have an air gap, make a high loop with the drain hose before connecting it to the garbage disposal or the sink drain tailpiece.
https://www.movementplumbing.com/blog/how-to-install-a-dishwasher
Click Here Report this page